817-465-6902

Cedar Hill Plumbing Repair Blog

Tips for homeowners on residential plumbing, repairs, and maintenance.

Dishwasher Maintenance Advice

Leftover food fragments that have stayed on the dishes that you have placed in the dishwasher, can cause a blocked, filthy dishwasher drain. For your dishwasher to correctly run, the drain has to be clean and without food and other debris. Cleansing a dishwasher drain is not as difficult as it seems and can be carried out by the typical Cedar Hill TX resident in a brief duration of time.

All About A Dishwasher Drain

A normal dishwasher drain is made up of a versatile hose secured at one end, to a dishwasher base or system, and at an additional end, to a drainage pipe or garbage disposal. Usual plumbing devices such as the plumber’s snake and plunger can not easily gain access to the within of a dishwasher drain. The only technique of cleaning the drain is to take apart the dishwasher to reach the drain.

You need to first take the essential security precautions prior to starting to clean your dishwasher drain. The dishwasher must be totally unplugged from the socket. You can continue with the task when you have verified that the electrical power is disconnected.

Started by clearing the dishwasher and getting rid of the dish racks so that you can see the drain. The drain is found at the bottom, center of the dishwasher, and can typically be found beneath the drain grate. This drain grate can be eliminated by either unscrewing the screws that are securing it, or simply popping the grate out. Various choices are provided depending upon the dishwasher you have.

Utilizing soapy water and a scrub brush or a toothbrush, clean the within of the drain and the grate area. The drain area should then be rinsed with clean water, and the drain grate need to be changed.

Plumbing technicians do not advise utilizing chemical cleaners for dishwasher upkeep. While caustic cleaners could offer a short-term fix, they will progressively hurt your appliance. Natural techniques are mostly advised. To clean your dishwasher drain out without using chemicals, put one-half cup of salt, one cup of baking soda, and two cups of white vinegar into the drain. Pour the ingredients exactly in that order. The chain reaction of the mixture will clean the drain.

Dishwasher Drain HosesDishwasher Repair Cedar Hill TX

Often times when you have a clogged dishwasher, it will be found in the drain hose, opposed to the drain itself. While you have the dishwasher open and the power off, find the drain hose. It is possible that the hose links to your garbage disposal. The owner’s handbook of your dishwasher will provide you with the understanding needed for your details model.

After you have actually found the hose, it must be detached from the back of your dishwasher by unscrewing the screws from the kick plate. The kick plate is found simply underneath the door of your dishwasher. Place a container on the floor to catch any debris that might fall from the hose. Pinch the ends of the clamp, and slide it down the drain hose to unhook it from the dishwasher. Place the hose over the container to get rid of any obstructions or waste. Run water with the hose to make sure that it is clean. The drain hose is now prepared to be reattached to the dishwasher.

The Dishwasher Is A Low Maintenance Appliance

If regularly and properly utilized, the drain needs to just need to be cleansed every six months. However, if you see a foul-smelling odor, that is the first sign of a clog, and a hint that your dishwasher drain should be cleaned.

A stopped up washing machine drain can result in a myriad of troubles for a resident. Not only can a blocked drain potentially mean inefficient draining of water, it can also slowly cause overflow. Cleansing a washing machine drain is basically an easy procedure, and in the end, will produce remarkable operation from your home appliance.

Prior to beginning a job with electrical devices, you need to unplug them to avoid unexpected shock.

How to Clear Obstructions From A Washing Machine Drain Is Simple

The drainage pipe is a large, versatile pipe located on the back of the washing machine. It is connected with four screws and a plate. Initially, get rid of the screws from home plate with a screwdriver, and separate the pipe from the cleaning device. It is suggested to hold the pipe over a bucket to clear out any water that stays in the drain.

Detach the cleaning machine drain hose from the drain pipe. The curved end of the hose is situated on the top of the pipe, and is typically held by a piece of plastic tie or wire. Making use of wire cutters or scissors, cut the wire or tie to unleash the drain hose.

Next, place a plumber’s snake into the drain pipe of the washing machine. Continue to advance it forward up until you meet resistance. When this occurs, tighten the wing nut on the front of the plumber’s snake, and twist the rotation knob on the backside of it. This will assist to split up any obstructions. Keep rotating the snake. Repeat this same procedure up until you no long feel resistence. This shows that the drain is clear. Slowly pull the plumbing snake out of the end of the drain pipe. If there was a clog in the drain, an item or mass will bring out the snake.

The drainage pipe can be replaced by reinsertion of the plate and screws. To eliminate any remnants of debris, run a cycle without any garments through your washing machine.

For minor construct up and little blockages, there are non-caustic remedies that are ideal for cleansing washing machine drains. To use this homemade recipe, drain all of the water out of your washing machine. Pour one cup of baking soda into the drain of your equipment. Then, pour 2 cups of boiling water into the drain. Allow 10 minutes for the mixture to procedure. Next, include an additional cup of baking soda straight followed by one cup of vinegar. Using a rubber stopper, plug the drain. The reaction of the active ingredients need to eliminate any undesirable material, and liquefy any small blockages. Pour a minimum of a half a gallon of boiling water after 10 minutes to purge the staying rubble with the plumbing system.

For a more relentless obstruction, a more powerful solution will have to be utilized. For this blend, you will require cleaning soda. This can be discovered in the laundry detergent section of the grocery establishment. Pour one cup of the cleaning soda down the drain. Let this sit in the drain for several hours. Then, pour one cup of baking soda and one-fourth cup of salt into the drain. These parts can sit in the drain as little as one hour, and as long as over night. Pour a compound of 2 cups of white vinegar and two cups of water gradually down the drain, waiting up until the foaming subsides. Lastly, douse the blend with hot water.

If you at any time feel uneasy cleaning out your washing machine drain, give us a call for help.

Click to print a PDF of this article.

Cedar Hill Leaky Garbage Disposal Repair

Cedar Hill Leaky Garbage Disposal Repair

If there are indications of a water leak underneath one’s ones Cedar Hill kitchen sink, find out if the water is leaking while the garbage disposal is running. If that is the case, there could be a few different problems. The good news is, many issues with garbage disposals which cause leaks are a rather simple plumbing repair to fix without an expert.

Although the water might appear to be leaking from the bottom of the disposal, the leak could actually be in another place. There are four primary areas that tend to leak. They are, the sink flange, the dishwasher hose, the drain, and directly underneath the garbage disposal. Keep reading to learn more about the more common troubles with garbage disposal leaking and ways to mend them.

Typical Garbage Disposal ProblemsGarbage Disposal Repair Cedar Hill

Sink Flange
The sink flange is where the garbage disposal and the sink meet. In order to know if this is the issue, plug the sink and fill it slightly under 1/2 way with water. Pour food coloring into the water. If there is any water dripping before the sink gets unplugged, the problem is with the sink flange. If this is the case, the sink flange seal is likely worn out. In order to fix this problem, one would need to remove the garbage disposal from the sink and seal the flange up again.

Drain Line or Dishwasher Hose
If there was no water dripping before the sink was unplugged, unplug it to locate the source of the leak. The dishwasher hose is pretty quick to find. It’s where the hose and the garbage disposal link. The drain line is where the drainage pipe and the disposal link up. Both issues can also be due to a damaged seal. In any case, the seal will, once again, need to be fixed. However, the process for resealing the disposal’s connection to the dishwasher hose or the drain pipe may vary based on the disposal.

Garbage Disposal Basin
In cases where the water is dripping straight out of the bottom of the garbage disposal, the seals within the basin are likely worn out. These seals can be restored, but, there are a number of seals within the garbage disposal. So, if one breaks, yet another break will, often, soon follow. In this predicament, it can be a good choice to have the garbage disposal replaced.

If the garbage disposal is still causing issues or there are still signs of water damage on the bottom of the sink cabinet, contact us. We can get the necessary Cedar Hill Plumbing Repair done quick.

Cedar Hill Garbage Disposer Repair

Click to print a PDF of this article.

How to Use a Plunger Correctly

So this article will either be upon a subject you have not had to ever think about, or one that you surely have some knowledge on. In any event, we think it is recommended to have a very good understanding of exactly how a toilet plunger operates should you need to use one fast, which is generally the situation for a Cedar Hill Plumbing Repair. However, plungers are additionally a handy tool to utilize with a sink clog too, not just a toilet.

The Mechanics of a PlungerCedar Hill Toilet Repair and Cleaning

We are going to presume most people understands what a plunger looks like. The only distinction among just how most are created is some have a flange on the bottom, and some are fashioned similar to a cup. This can help establish a more powerful seal while pushed within the toilet.

Plungers work on the essential concept of pressure, and that is the most critical part of any plumbing system. A balance in water pressure is exactly what it truly is all about. Any time one is suffering from a clog in a pipe, by adjusting the pressure of the water on the top of the obstruction enables the blockage to separate, or to move through the plumbing pipe.

To enable a plunger to create the desired pressure to dislodge a clog, it needs to seal securely against the toilet opening or sink drain. Angle the plunger somewhat when it goes into the water. This will push air outside of the bell. A cup or bell packed with water will push water down upon the obstruction when the plunger is pushed. Pulling back up on the plunger then will decrease the pressure on the water.

Since there is also air behind the blockage, that applies pressure upon it. The change from high to low water pressure makes a push and pull on the blockage that either breaks it up or pushes it through the water pipe.

Using a Plunger with a Toilet

With the general physics explained, here are the common tips for making use of the plunger on a toilet. First, put the cup or flange of the plunger into the toilet at an angle to allow air to get out and after that cover the toilet opening at the bottom of the toilet bowl to form a tight seal. When the air is gone from the cup or flange of the plunger it functions the best to use a vertical motion with it, not an angled one from initially putting the plunger within the toilet. Push down gently on the plunger to produce pressure, for the goal is to generate the water pressure on top of the clog. Then, pull up quickly with the plunger to create a vacuum to move the clog up. The procedure may well have to be repeated more than once to loosen the blockage.

Take care not to push down too forcefully with the plunger for if a lot of pressure is generated, it will harm the toilet tank or the wax seal. It is even possible to crack a water pipe as well. It is always best to start with easy pressure or strength and increase it as needed.

In addition, do not utilize chemical drain cleaners and then utilize a plunger. It is very easy to splash the chemicals upon oneself.

If you happen to be in need of an emergency drain cleaning or plumbing repair, don’t be reluctant to get hold of us quickly for any sort of help in Cedar Hill TX!

Click to print a PDF of this article.

Blocked Plumbing Vent Problems

Plumbing vents are in fact vertical pipes which go from water and sewer pipes, through the walls, then right up and out of the roofing of the house. Such vents let air into the piping which will hold pressure in balance which allows everything to move along the pipes efficiently and rapidly. These vents may without difficulty get plugged, though, which may lead to plumbing clogs. Plumbing clogs might manifest in several different ways which include bad smells, slow-moving drains, and backups. Drain and sewer line blockages occur commonly and for many reasons, but there are a few indications to look for whenever you are concerned a plumbing vent could be blocked.

What Leads to Plumbing Vents BlockagesPlumbing Vent Cedar Hill

There are actually numerous ways plumbing vents might get clogged or blocked. Given that they are simply open pipes sticking out of the roof, it is somewhat simple for them to get blocked or stopped up. Here are a few of the primary ways plumbing vents get blocked up:

Animals
Bird nests
Foliage
Corrosion

Many of these are without difficulty taken care of, though some problems, like rust, are more challenging. Plumbing vents are the same as every other pipe and, as time passes, probably will have to be replaced because of rust. It is advisable to be familiar with exactly how old your pipes are so you recognize when that time could be approaching.

Indications of a Cedar Hill Plumbing Vent Blockage

There are three principal indicators that a plumbing blockage is being brought on by a vent blockage; toilets gurgling whenever flushed, slow-moving drains, and sewer odors. Although these types of problems may, obviously, be resulting from other elements, a plumbing vent clog may be a simple mend for many. As stated earlier, frequently with vent blockages, repairs aren’t as devastating as having to replace a pipe or total vent system. In cases where a gurgling commode is the issue, it is probably a good sign. In nearly all scenarios, gurgling toilets do not gradually get worse, it simply starts gurgling some day before it gets repaired. The gurgling is commonly caused by an obstruction in the entry of the pipe such as a bird’s home or leaves. This issue occurs since not enough air is getting into the water system via the plumbing vent causing there to be excessive pressure. Whenever you go to flush the toilet the water is struggling with the pressure when it’s attempting to move down the drain.

Slower drains may be brought on by a number of plumbing problems, but the plumbing vent being blocked can cause this too. For the exact same reason as the commode making a gurgling sound when it is getting forced down a drain having high pressure, other drains will drain more slowly. Other drains in the home are not being forced down, which means that they aren’t being forced to battle the high pressure in the plumbing, the water simply runs down the drain at a sluggish rate, when a blockage within the vent is the culprit. An undesirable smell of sewer gas can be another issue that could be due to a blocked vent or it may be a result of something different.

The best thing to do if you are encountering any of these 3 issues would be to have a specialist take a look at the vent entry on the rooftop. If perhaps the pipe looks okay, in that case, at least, the vent will be eliminated. The best preventative maintenance for plumbing vents is to monitor the roofing to make sure there are no over hanging branches and keep track of how old the plumbing is in your house. Have us visit once a year to examine your plumbing to help prevent an unwanted Plumbing Repair in Cedar Hill TX.

Click to print a PDF of this article.

Winterizing Home Plumbing

Being a Cedar Hill property owner, it really is critical to make certain to take care of ones property as best as achievable so it can be energy effective, and can keep its worth in the future. Having said that, it happens to be essential to carry out a number of home upkeep measures each and every fall season ahead of the winter months arriving. The cold temperatures are usually hard on exterior plumbing and fixtures if water is left within them. Harm could be done to the plumbing in ones property also. What exactly are the finest methods to winterize ones plumbing with regard to the cold temperatures then? The following is everything that we advise to carry out to counteract any sort of unnecessary plumbing repair in Cedar Hill this wintertime.

Actions for Cedar Hill Homeowners to Winterize Outdoor PlumbingPlumbing Repair Cedar Hill Winterizing

Outside Faucets
Be sure you understand exactly where all of the exterior faucets happen to be to be found. All of the hoses should be unconnected and drained to store through the winter season. Take off splitters or any type of timers, or whatever else that could be fastened to any of the faucets.
Shut-off Valves
Each outdoor faucet ought to have a shut-off valve located inside the home somewhere. Find every one of them and move the valve to the off placement.
Drain Outside Faucets
Switch on all of the faucets to drain any water remaining within them. If the water remains running, check out the valve to make sure that it truly is shut off. One could keep the faucet handle switched on through the the winter season.  Here are some tips from This Old House.
Increase Protection
All outside plumbing piping may and ought to be safeguarded all the more through insulating all of them. Insulation sleeves may easily be added on right over top present plumbing water lines and almost all local hardware or diy stores sell them to buy. Likewise, winterize outside faucets using insulated faucet covers to provide additional defense to faucets. Or maybe, get a freeze-proof faucet having a uniquely made tube which goes to the shut-off valve, which may perhaps be hooked up by property owners. As soon as the faucet is switched off, water inside it will quickly drain out by means of this tube.

When you are generally not positive what to accomplish with any of your plumbing in the home, do not forget to make contact with Plumbing Repair Cedar Hill with any problems you could have. We are available at any hour to help you. From a drain, sewer, plumbing fixture, to a water heater matter, we can easily repair every one of them!

Click to print a PDF of this article.

Water Heater Troubleshooting

Hot water heaters are one of a property’s toughest working appliances. Day or evening, it’s making perfectly heated water at any time when you want it. When it suddenly is no longer working adequately, many of us often overreact.

Fortunately a non-functioning water heater does not constantly indicate an expensive repair. Before making an emergency call to A Monsey & Son Plumbing, we suggest checking the trouble yourself first.

Cedar Hill Water Heater Repair Troubleshooting

Pilot Light CheckCedar Hill Water Heater Repair

For gas water heaters first eliminate the small panel which is found on the bottom of the system and check to notice if the pilot light is illuminated.
See if may relight in case it is not lit. If it remains lit, one will probably be able to hear that the water heater should begin working correctly once more. The pilot light may perhaps need cleaned out or the thermocouple may need replaced when the pilot light will definitely not remain lit.

Thermocouple Replacement

The term thermocouple may perhaps seem like a really complex term, but it’s a component on ones water heater that can easily be replaced. A Monsey & Son Plumbing would recommend having us conduct the replacement but the methods below are for instructional objectives.

Consult the owner’s handbook. It needs to have suggestions for the best ways to remove and change the thermocouple.
Turn off the gas before removing anything at all from the water heater.
Using the guidelines in your user’s guide, remove the thermocouple by separating it from both sides of the pilot light. The new thermocouple on the water heater is required to be cut to the correct length.
The gas may then be turned back on and test for leaks, then the pilot light may be lighted again.

Press the Water Heater Reset Button

For property owners with an electric water heater, discover the location of the reset button and press it till a click is heard.
If a click is definitely not heard, or it fails to restart the water heater, reset the breaker.
If a breaker reset doesn’t do the technique, the thermostat may well require being replaced.

Thermostat Replacement

Both the power to the water heater and the switch on the breaker will require being turned off. Basic safety with electricity needs to be used!
Use the owner’s handbook to find the thermostat wires, then separate them.
After taking out the thermostat we will evaluate to observe its problem. If it is faulty, we will have to change it.

Heating Element Replacement

While the power is still off, the access panel on the water heater may be removed.
The terminal screws may be loosened and the wires may be drawn far from the heating element.
We would next test each part of the element to verify if they are defective, and replace them as required.

These water heater troubleshooting techniques ought to help get ones heater going once more. A Monsey & Son Plumbing is definitely here to assist, and so don’t wait to contact us today for any Water Heater Repair Cedar Hill TX help.

Click to print a PDF of this article.